Tally Printer Code Errors And Messages

Tally printer code errors and messages are error messages that get displayed on the tally printers when there is an issue with the printer that requires an immediate section. In this blog, we have talked about common tally printer codes and messages. This guide will help you clear the errors on your tally printer and get back to printing properly.

Eject Error 

Eject error is a very uncommon Tally printer code errors and messages. Here are some of the common causes of eject errors in tally printers

1. The paper you are using to print is damaged
2. The paper path from where the printer comes out is blocked
3. The print head gap on the print head is too small 

Fix Eject Error on the Tally printer

1. Open the printer covers.
2. Check the paper path for any kind of obstruction
3. Clear out the obstruction
4. If there is dirt inside the printer, clean it with a cloth
5. Manually adjust the print head gap of the printer
6. Close all the printer doors 
7. Check if the papers are in good condition
8. Load all the papers in the paper tray
9. Close the printer doors, connect it to power, and then run a print test.

Tally cartridge problem

The Tally cartridge problem is one of the most common tally printer code errors and messages. Here are some of the most common tally cartridge problem

1. The computer is unable to recognize the ink cartridge 
2. The ink cartridges installed in your printer might have run out of ink 
3. The cartridges are not correctly installed on your printer resulting in a tally cartridge problem

How to solve the Tally cartridge problem

Solving the Tally cartridge problem is very easy. In just 9 steps, you can solve the issue. Follow the instructions to complete this cartridge troubleshooting

1. Disconnect the wires of the tally printer after turning it off 
2. Open the doors of the print, open the front door only
3. Take out all the ink cartridges one by one 
4. Check all the ink cartridges 
5. If the ink cartridges have dried out or if there is not enough amount of ink left in the printer, replace these ink cartridges with a new one. 
6. Clean all the cartridges 
7. Push the ink cartridges into the printer into their respective slots 
8. Close the doors of the printer 
9. Print a page to see if the tally cartridge problem is solved or not

Ink system failure tally printer

Ink system failure tally printer is a very tough issue to fix by yourself but this troubleshooting guide makes it really easier. Follow the steps below to fix this one of the common Tally Printer Code Errors and Messages.

1. To switch off the printer, press the power button. If the printer does not switch off, pull the power line from it.
2. Unplug the power cord from its power source.
3. Wait a minute or two before turning on the printer.
4. Connect the electrical cord to both a wall socket and the printer.
5. Switch on the printer to repair the ink system failure tally printer.
6. Cleanse the ink cartridge vents.
7. Glue remnants from the sticker or particles on the cartridge vent could end up in a tally cartridge problem
8. Open the door or cover to reveal the cartridge access compartment. allow till the carriage has stopped moving before continuing.
9. Push in the tab on a cartridge, and then pull the cartridge from the slot.
10. Do not leave the ink cartridges outside the tally printer for more than 20 minutes. Doing so can result in a tally cartridge problem or some other 
11. Removing the tally ink cartridge
12. If the cartridge has the orange pull tab attached, remove it.
13. To clean the printer’s orange tape, use a pin or paper clip to remove dirt or extra glue from the vent on top of the cartridge.
14. Reinsert the ink cartridge into the color-coded slot, then press down until it snaps in place.
15. Repeat the above procedure to clean the vents on the remaining cartridges.
16. Install a new set of cartridges to resolve certain Ink system failure tally printer
17. Get new cartridges and install them 
18. It is recommended that you use genuine cartridges made specifically for use with tally printers
19. Open the door or cover to the cartridge access compartment. Wait until the carriage has stopped moving before proceeding.
20. Remove a cartridge, then insert a fresh one into the slot.
21. Follow these instructions to replace the remaining cartridges.